ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.
| Author: | Tojalabar Tozragore |
| Country: | Benin |
| Language: | English (Spanish) |
| Genre: | Photos |
| Published (Last): | 16 March 2009 |
| Pages: | 384 |
| PDF File Size: | 20.15 Mb |
| ePub File Size: | 13.97 Mb |
| ISBN: | 715-3-46624-775-1 |
| Downloads: | 48529 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Goramar |
Types and L are weldable by most fusion or resistance welding techniques.
Only annealed conditions of grades speci? The noncontrolling factor normally will exceed considerably the speci? HardC Elongation in 2 in. A — 10 Standard Speci? In atsm annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.
However, in the case of dispute, tests shall be made by pressure. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: Users of this standard are aztm advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely a666-100 own responsibility.
Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?
This standard has been approved for use by agencies of the Department of Defense. This revision of Speci? Material Test Report and Certi? Originally approved in C Annealed material that naturally meets mechanical properties may be applied. Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques.
These alloys represent an excellent combination of corrosion resistance and fabricability.
304 and 304L Stainless Steel
In case of dispute, the offset method of determining yield strength shall be used. HRC typical L Ann 25 min.
The values given in parentheses are for asm only. A number in parentheses indicates the year of last reapproval. The choice of test method for materials in conditions other than annealed shall be at the option of the seller.
Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent asfm the weld pool. Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides. One bend test shall be made from one end of each coil. The values obtained in this manner should not, however, be taken as the actual yield strength for 0. Hard Elongation in 2 in.
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Number of Tests 8. Permission rights to photocopy the standard may also be secured from the ASTM website www. Sstm out what NKS can do for you.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Current edition approved Sept. Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
D PSS means plate, strip, sheet. Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Type L LN Last previous edition approved in as A — Rockwell B 95 95 Types and L cannot be hardened by thermal treatment. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Maximum unless otherwise indicated. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres. Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part.
If filler metal is required, Type is normally used.