ASTM D – Medición de EPH – Download as PDF File .pdf), Text File .txt) or read online. Standard ASTM D The following devices are in accordance with ASTM D ZMK – Road Marking Control Kits. Specially designed for road . Technical Specification. STANDARDS: ASTM D A, AS/NZS , BS CB,. ISO A, ISO B, JIS K , NF T, US.
|Published (Last):||6 April 2014|
|PDF File Size:||13.15 Mb|
|ePub File Size:||15.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
Already Subscribed to this document. These gauges are not designed as ‘throw-away’ items and should not be compared to gauges that are ‘printed’ or silk-screened. Proceed to Checkout Continue Shopping. Caltech Engineering Services offer disposable plastic wft gauge is designed for once only use, simply place in the wet paint note the wet paint thickness, Allow paint to dry and retain for future ISO record or customer requirements.
The wet film thickness WFT of the coating lies between the values of the smallest un-coated dry tooth or notch and the largest coated wet tooth or notch. A ‘drag’ mark would indicate that the tooth or notch should have coating ‘clinging’ to it.
This standard is also available to be included in Standards Subscriptions. Instructions On How To Use A ‘Wet Film Thickness Gauge’ Place the wet film thickness gauge at ninety degrees to the coated substrate and penetrate the surface of the coating with the notched or toothed side of the gauge until the substrate is firmly contacted. Be sure to clean the gauge with an appropriate solvent after use. Add to Alert PDF. Please first verify your email before subscribing to alerts. When wet film thickness is measured with the gauges on rough substrates, the thickness measurements made will most likely be from the surface ‘peaks’ and the wet film thickness measurement will represent the minimum overall wet film thickness.
The mode of operation is similar to measuring ‘wet’ coatings.
Consequently, the results from the notch d4441 are not to be used to verify the nonvolatile content of a coating. Your Alert Profile lists the documents that will be monitored. All markings and graphics are etched and black filled. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
Such a gage is applicable to coatings on flat substrates and to coatings on articles of various sizes and complex shapes where it is possible to get the end tabs of the gage to rest in the same plane on the substrate. These gauges are also commonly known as: You may delete a document from your Alert Profile at any time. Correction of the film after it has dried or chemically cured requires costly extra labor time, may lead to contamination of the film, and may introduce problems of adhesion and integrity of the coating system.
Also notched gages can be very useful in the shop and field for determining the approximate thickness of wet films over commercial articles where size s and shape s are not suitable for measurements by other types of gages.
These gauges meet the requirements of the following International Standards: We have no amendments or corrections for this standard. With some flat coatings the dry film thickness is higher than that calculated from the wet film thickness.
Subscription pricing is determined by: The thickness of dry powder coatings may also be measured with these type of gauges. The gauges are precision manufactured from hardened grade stainless steel. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
It measures the thickness immediately after the coating has been applied on the material. The gauges incorporate a series of notches cut into their sides much like the teeth on a comb. Wet film thickness is measured to determine the correct dry coating thickness.
ASTM D – Zehntner GmbH
Manufacturing and Office Location: The teeth or notches on each side of the gauge are referenced to each other. Box Syracuse, NY U. Notch gages may, however, be used on nonuniform surfaces, like concrete block, that s4414 too rough to use the Interchemical and Pfund gages.
See dimensional drawing below.
How to Use a ‘Wet Film Thickness’ Gauge
The thickness of powder type coatings may also be measured before curing. Examples of such items are ellipses, thin edges, and corners. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Need more than one copy? Wait several seconds to allow the teeth or notches of the gauge to become ‘wetted’ by the coating, then withdraw the gauge vertically keeping it at ninety degrees to the substrate.
On curved surfaces such as pipes, cylinders, sstm.
How to Use a ‘Wet Film Thickness’ Gauge
The teeth or notches are graduated in MILS 0. Model A Gauges The gauges are precision manufactured from hardened grade stainless steel.
Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. The gauge may now be read to determine the wet film thickness.